Manual For Elit Diopter Sights

Return to site

Manual For Elit Diopter Sights

Manual For Elit Diopter Sights Scope
Rear Diopter Sight
Manual For Elit Diopter Sights For Free
Manual For Elit Diopter Sights For Sale
Diopter Sights For Sale
Type K Diopter Sight manual
Translated from French 

 Swiss Diopters on the firing line
Hey, 22lrfan, I also have a FSR 96 Swede, has a Soderin diopter peep sight. Mine is missing the globe front sight, I think it is made by Elit? Cheapest I have seen one is $100. Let me know if you see a cheaper one, please. Otherwise I am putting a Lyman, Williams, or Redfield on it. Designed to clamp to any 11mm dovetailed receiver this precision sighting instrument will provide an enhanced sight picture and highly repeatable micrometer sight adjustments. Can be used on Daisy Match Grade Avanti models 853 and 953 target rifles but ONLY if you use a globe front sight. Steel body and rail clamp, black, baked on finish. Whether you're upgrading or replacing, Pyramyd Air has plenty of options when it comes to installing new open sights on your airgun. We stock a full selection of front sights and accessories, rear sights and accessories and sight sets from brand names like Air Arms, Air Venturi, AirForce, Crosman, Daisy, Feinwerkbau FWB, Weihrauch and others. Sight is moved every tima the rifle is cocked. The ANSCHUTZmicrometer peep. Sight and tunnel foresight with elements, used with the ANSCHUTZ Model 54 small bore Target Rifles, can also be used with this Match Air Rifle. This is most economical for the shooter as the some set of sights can be used with both rifles.

 Front Cover
ContentsPage
Description 2-3
 Characteristics Techniques 2-3
 Front Sight Installation 4-5
 Rear Sight Installation 6-7
 Adjusting the Line of Sight 8-9
 Aiming 10
 Parts List (not translated) 11-15
Description; The type K diopter plus front sight is a aiming system that can be mounted on any K31 without any modification to the weapon.
 Technical characteristics;
 The diopter is adjustable for distances of 50m to 600m. It comes with an eyepiece with a perforated disc that has six sighting holes for the convenience of the shooter and measuring, respectively; 1,0mm, 1,2mm, 1,4mm, 1,6mm, 1,8mm, 2,0mm.
 Windage and elevation adjustments are made with two adjustment screws. The elevation screw should be adjusted in the following manner;
 shot too high-turn elevation screw clockwise
 shot too low - ' ' ' counter-clockwise
 windage adjustment;
 shot to left- turn adjuster to the right
 shot to right- turn adjuster to the left
 The adjustment screws for both elevation and windage are furnished with click stop graduated lines that represent 2 centimeters each at 300meters distance.
 The sight line distance is 760mm.
(Pages 2-3)

 Mounting the front sight;
 -back off the mounting bolt (27) until the threads are no longer visible.
 -with arrow (26) pointing towards target, slide the front sight assy. over the rifle's fixed sight until it seats
 -firmly press down on the front sight barrel while while tightening the set screw (29).
 - check for play in all directions (there should be none).
(Pages 4-5)
Mounting the diopter (rear sight);
 -Unscrew (without forcing) the knurled mounting screw (9).
 -using your left hand, set the diopter assembly in place onto the receiver with the forward leg (7) set on the wide part of the ejection port (8)and the eyepiece just on top of the rear of the receiver.
 -hand tighten to set screw, then finish tightening with the factory tool.
 -hand check for play in all directions (there should be none). 
(Pages 6-7)

Manual for elit diopter sights replacement

Adjusting the line of sight;
 -Once in place on the receiver, make sure that the eyepiece is centered in windage (24) and elevation (25) by looking at the long white reference lines (C&D) (opposite of the side you aim through).
 -next, set your factory front sight in position 10, representing 1000 meters. Now look through the diopter and line everything up on the target. The sight picture should be perfectly concentric and tangent. 
(Pages 8-9)
Aiming process:Align the front tunnel and rear tunnel to give a concentric sight picture, where the target appears just above the front sight post.
(Page 10)
(Pages 12-13)

 Shooter's card
To see the original click here
Acknowledgements: Thanks to Vaudois for the translation, and thanks to Carlos for the scans.
To return to the Schmidt-Rubin Aftermarket Sight page click here
Manual For Elit Diopter Sights ScopeType K Diopter Sight manual
Translated from French 

 Swiss Diopters on the firing line
Rear Diopter Sight
 Front Cover
ContentsPage
Description 2-3
 Characteristics Techniques 2-3
 Front Sight Installation 4-5
 Rear Sight Installation 6-7
 Adjusting the Line of Sight 8-9
 Aiming 10
 Parts List (not translated) 11-15
Description; The type K diopter plus front sight is a aiming system that can be mounted on any K31 without any modification to the weapon.
 Technical characteristics;
 The diopter is adjustable for distances of 50m to 600m. It comes with an eyepiece with a perforated disc that has six sighting holes for the convenience of the shooter and measuring, respectively; 1,0mm, 1,2mm, 1,4mm, 1,6mm, 1,8mm, 2,0mm.
 Windage and elevation adjustments are made with two adjustment screws. The elevation screw should be adjusted in the following manner;
 shot too high-turn elevation screw clockwise
 shot too low - ' ' ' counter-clockwise
 windage adjustment;
 shot to left- turn adjuster to the right
 shot to right- turn adjuster to the left
 The adjustment screws for both elevation and windage are furnished with click stop graduated lines that represent 2 centimeters each at 300meters distance.
 The sight line distance is 760mm.
(Pages 2-3)
Manual For Elit Diopter Sights For Free
 Mounting the front sight;
 -back off the mounting bolt (27) until the threads are no longer visible.
 -with arrow (26) pointing towards target, slide the front sight assy. over the rifle's fixed sight until it seats
 -firmly press down on the front sight barrel while while tightening the set screw (29).
 - check for play in all directions (there should be none).
(Pages 4-5)
Mounting the diopter (rear sight);
 -Unscrew (without forcing) the knurled mounting screw (9).
 -using your left hand, set the diopter assembly in place onto the receiver with the forward leg (7) set on the wide part of the ejection port (8)and the eyepiece just on top of the rear of the receiver.
 -hand tighten to set screw, then finish tightening with the factory tool.
 -hand check for play in all directions (there should be none). 
(Pages 6-7)
Adjusting the line of sight;
 -Once in place on the receiver, make sure that the eyepiece is centered in windage (24) and elevation (25) by looking at the long white reference lines (C&D) (opposite of the side you aim through).
 -next, set your factory front sight in position 10, representing 1000 meters. Now look through the diopter and line everything up on the target. The sight picture should be perfectly concentric and tangent. 
(Pages 8-9)
Aiming process:Align the front tunnel and rear tunnel to give a concentric sight picture, where the target appears just above the front sight post.
(Page 10)
(Pages 12-13)

 Shooter's card Canon laser shot lbp 1210 driver for windows 10.

Adjusting the line of sight;
 -Once in place on the receiver, make sure that the eyepiece is centered in windage (24) and elevation (25) by looking at the long white reference lines (C&D) (opposite of the side you aim through).
 -next, set your factory front sight in position 10, representing 1000 meters. Now look through the diopter and line everything up on the target. The sight picture should be perfectly concentric and tangent. 
(Pages 8-9)
Aiming process:Align the front tunnel and rear tunnel to give a concentric sight picture, where the target appears just above the front sight post.
(Page 10)
(Pages 12-13)

 Shooter's card
To see the original click here
Acknowledgements: Thanks to Vaudois for the translation, and thanks to Carlos for the scans.
To return to the Schmidt-Rubin Aftermarket Sight page click here
Manual For Elit Diopter Sights ScopeType K Diopter Sight manual
Translated from French 

 Swiss Diopters on the firing line
Rear Diopter Sight
 Front Cover
ContentsPage
Description 2-3
 Characteristics Techniques 2-3
 Front Sight Installation 4-5
 Rear Sight Installation 6-7
 Adjusting the Line of Sight 8-9
 Aiming 10
 Parts List (not translated) 11-15
Description; The type K diopter plus front sight is a aiming system that can be mounted on any K31 without any modification to the weapon.
 Technical characteristics;
 The diopter is adjustable for distances of 50m to 600m. It comes with an eyepiece with a perforated disc that has six sighting holes for the convenience of the shooter and measuring, respectively; 1,0mm, 1,2mm, 1,4mm, 1,6mm, 1,8mm, 2,0mm.
 Windage and elevation adjustments are made with two adjustment screws. The elevation screw should be adjusted in the following manner;
 shot too high-turn elevation screw clockwise
 shot too low - ' ' ' counter-clockwise
 windage adjustment;
 shot to left- turn adjuster to the right
 shot to right- turn adjuster to the left
 The adjustment screws for both elevation and windage are furnished with click stop graduated lines that represent 2 centimeters each at 300meters distance.
 The sight line distance is 760mm.
(Pages 2-3)
Manual For Elit Diopter Sights For Free
 Mounting the front sight;
 -back off the mounting bolt (27) until the threads are no longer visible.
 -with arrow (26) pointing towards target, slide the front sight assy. over the rifle's fixed sight until it seats
 -firmly press down on the front sight barrel while while tightening the set screw (29).
 - check for play in all directions (there should be none).
(Pages 4-5)
Mounting the diopter (rear sight);
 -Unscrew (without forcing) the knurled mounting screw (9).
 -using your left hand, set the diopter assembly in place onto the receiver with the forward leg (7) set on the wide part of the ejection port (8)and the eyepiece just on top of the rear of the receiver.
 -hand tighten to set screw, then finish tightening with the factory tool.
 -hand check for play in all directions (there should be none). 
(Pages 6-7)
Adjusting the line of sight;
 -Once in place on the receiver, make sure that the eyepiece is centered in windage (24) and elevation (25) by looking at the long white reference lines (C&D) (opposite of the side you aim through).
 -next, set your factory front sight in position 10, representing 1000 meters. Now look through the diopter and line everything up on the target. The sight picture should be perfectly concentric and tangent. 
(Pages 8-9)
Aiming process:Align the front tunnel and rear tunnel to give a concentric sight picture, where the target appears just above the front sight post.
(Page 10)
(Pages 12-13)

 Shooter's card Canon laser shot lbp 1210 driver for windows 10.
To see the original click here
Acknowledgements: Thanks to Vaudois for the translation, and thanks to Carlos for the scans.
Manual For Elit Diopter Sights For SaleTo return to the Schmidt-Rubin Aftermarket Sight page click here
Diopter Sights For Sale